Leading 10 usual forklift accidents ， forklift procedure need to pay attention to these issues ！.

Don't undervalue the forklift at the office. If the procedure is not good, there will be severe crashes in minutes, and there are many accidents entailing forklifts.

Case 1: The forklift cargo obstructed the chauffeur's view, and the individual ahead could not be found, causing a rolling mishap.
Situation 2: In order to keep the equilibrium of the forklift when raising hefty goods, the employees utilized their body weight as the weight, which virtually triggered casualties.
Case 3: The width of the forklift cargo exceeds the allowable size of the course and hangs on the roadside rack, which nearly triggers an mishap.
Instance 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift raises the personnel illegally, the forklift motorist does not wear the safety belt, the forklift lifter drops and the motorist is squashed when the forklift rolls over.
Situation 7: The forklift driver did not use a seat belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure should focus on these issues ：.

Start.
1. Prior to starting, observe the environments, and after confirming that there are no barriers that impede the security of driving, honk the horn first and after that begin.
2. For automobiles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic stress ( atmospheric pressure) gauge must be secure before starting.
3. When the forklift begins with a load, the vehicle driver must first confirm that the load is steady and reputable.
4. The beginning has to be sluggish and constant.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground need to be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not raise the fork too high when driving. When getting in and leaving the job site or while driving, beware that there will certainly be no challenges in the sky. When the tons is traveling, the fork has to not be increased expensive, which will certainly influence the stability of the forklift. .
3. After unloading, the fork should be reduced to the normal driving position prior to driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal needs to be provided first. High-speed doglegs are restricted. High-speed doglegs will certainly create the vehicle to lose side stability and tip over. .
5. When the forklift is downhill, it is purely restricted to switch off the flame and slide, and it is forbidden to brake suddenly while driving with loads unless there are unique situations.
6. When the forklift is running, it needs to obey the website traffic rules in the factory and should maintain a particular safety distance from the automobile in front. .
7. When the forklift is running, the load must be in the lowest placement that does not prevent the driving, and the gantry should be effectively tilted back. The lots will not be increased other than when piling or loading. .
8. The height of the tons need to not obstruct the chauffeur's sight. In unique situations, when the product impacts the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to switch on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the manufacturing facility location is 5 km/h, and it has to drive safely at a reduced speed when going into the production workshop area. .
11. When the forklift is lifted, lifted or driven, it is restricted for workers to base on the fork to hold products and play a balancing role. .
12. If troubles are located, they will be repaired and reported in a timely manner, and they will certainly never operate with ailments or hide them.

loading and discharging.
1. When fork-loading products, the range between both forks need to be changed as required to make the lots of both forks balanced and not manipulated, and one side of the thing must protest the rack. .
2. It is forbidden to work with a solitary fork or make use of a fork top or pull. In unique conditions, safety indication should be established to remind bordering pedestrians. .
3. In the process of packing and unloading things, the forklift should be braked with the brake. .
4. The rate of the car need to be sluggish and steady. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled objects and injure people. .
5. When using a fork to fork the goods, the fork must be as deep as feasible under the lots, and it must be noted that the fork pointer should not touch other products or things. The load must be stabilized with very little back tilt of the gantry to ensure that the lots does not glide in reverse. The pole can be slanted forward somewhat when the lots is decreased to allow for easy positioning of the lots and extraction of the forks. .
6. It is forbidden to fork products at broadband and ram hard objects with the fork head. .
7. When the forklift is functioning, it is restricted for people to loaf the fork, so regarding avoid the collapse of the goods and hurt people. .
8. Straining is forbidden, and it is forbidden to make use of forks to lift personnel to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not allowed to utilize the brake inertia to slip, Electric Forklift Truck for Warehouse place, round or roll things. .
10. It is not permitted to make use of forks to pick, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the items on the fork are in the air. Prior to leaving the forklift, you have to unload the goods or lower the fork frame.
2. Draw the parking brake handle to dead or dispirit the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the chauffeur does not leave the car's line of vision and does not exceed 1 minute).
4. Remove the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance needs to be checked, and fuel, lubing oil and air conditioning water ought to be added.
2. Check the security efficiency of beginning, running and stopping.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, inspect whether the stress and temperature are typical.
5. After the forklift is running, the external leak ought to also be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to check prior to leaving the automobile;.
2. When you come across somebody before you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the cargo should be Stand-on Electric Pallet Stacker 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be too sharp to stop the tendency of " cost-free turning";.
6. Running up and down the slope must be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the gradient. When the gradient is greater than 10%, the lorry ought to be driven in reverse when worsening;.
8. When the forklift employees lug the goods and move forward, if they experience big or hefty items and go to the motorist's line of vision, they must take the turning around workout
.
The "Eight Prohibitions" ought to be adhered to in the procedure.
1. Solitary fork operation is not permitted.
2. It is not enabled to lift the goods for far away driving.
3. It is not allowed to grab the goods by passing on the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia pressure to pick up the goods.
6. It is not enabled to make use of stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring people to service the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on inclines
.
Vehicle parking is not permitted under the list below conditions.
1. Contours, slim roads, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the area with the exact same size as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844